Unfortunately, most homeowners find that plumbing issues tend to rear their head soon after a new property is purchased. These problems typically occur in bathrooms and kitchens. Eventually, nearly every homeowner has to face one type of plumbing issue or another. Using the following tips will help you with plumbing issues.
On very cold winter nights, allow your faucets to trickle slightly, especially if your pipes are located in a crawlspace. The running water prevents the pipes from freezing as quickly as they would otherwise. You can catch the water and use it for other household needs to prevent wasting it.
If you have issues with the plumbing making a hammering sound when you turn it off, check your water pressure. Any time your water pressure is above 80 PSI, you will hear extra water noise. This can be easily solved by the installation of a pressure-reducing valve, which can be done by most homeowners.
Do not let your faucet leak. Did you know a leaky faucet can waste about 150 gallons of water every day? If you have a leak, never ignore it. It could be coming from the faucet or the pipes. Continually check pipes and faucets for extra moisture or small leaks.
Making sure you know all of your problems so you can have them fixed by one plumber visit is very beneficial. Having them all fixed in one visit takes a lot of money off of your bill because you don’t have to pay for the visit multiple times so make sure you make a list first.
Use a strainer over your sink drain to catch food and other bits of material. Otherwise, you will likely get a clogged drain. Anytime there is something caught in your kitchen drain, you should clean it out. Bathtubs should be equipped with strainers as well, and they too will need to be cleaned regularly.
Keep your bathtub drain running well by pouring a cup of baking soda followed by a cup of vinegar down the drain each month. This will cause the vigorous bubbling you may remember from the “volcano” in a grade school science project, so be sure to close the drain with a stopper. Allow some time to pass, then follow up by pouring down boiling hot water. Doing this periodically should keep your pipes free of hair and soap scum.
Have you tried patching your pipe with the store-bought patching kits only to have that section of your plumbing continue leaking? Replacing the damaged pipe is a more permanent solution than patching. First, you must shut off the main water valve, and drain the water from the damaged section. Cut out the damaged section of the copper pipe, leaving about an inch of extra pipe on both sides of the damaged area. Remove corrosion from inside the pipes with a wire brush. Apply flux to the replacement pipe and the remaining pipe. Slide the piece of replacement pipe into place with couplings. Apply solder all around the joint, and use a propane torch to solder the replacement section into place.
While it may seem like a seemingly harmless thing to do, never run potato peels through your garbage disposal. The chemical make up of this seemingly harmless food allows the potato to turn into a thick, viscous substance that can wreak havoc on the disposal itself, with the potential to render it completely useless.
Drain the sediment from the bottom of your hot water heater twice a year to keep the hot water heater working at its optimal levels. Simply open the drain valve and allow the water to run out into a bucket until the water runs clear. Then close the drain valve.
If grout is stick within the line, it is likely useless to try cleaning it on your own. The grout can be broken up and sent further down. This works better with plastic piping than it does with metal. Usually, however, you will need to hire a professional for this issue.
Do you have a frozen drainpipe? You can use a garden hose to thaw it out. First of all, remove the trap from the drainpipe and insert the hose until it will not go any further. While lifting up the other end of the hose, pour hot water down it. Keep pouring hot water down the hose until the drainpipe thaws. To save time with cleanup, keep a bucket underneath to catch the water that overflows.
Make sure that the temperature of your home’s water heater is not above 120F. On older water heaters, be sure it is not above medium settings. When temperatures get higher than 120, scalding can occur. Also, having the settings above 120F, tends to use more energy than lower temperatures do.
If the water is not going into your dishwasher, the first thing you should do is shit off the water under the sink. Chances are that you have some kind of blockage, and keeping the water turned on could actually create a bigger problem. To fix the blockage, you may need to call a plumber.
The worst thing to have happen is a plumbing problem if you are unprepared to deal with it. All homeowners should have some basic plumbing tools, they should also be aware of a few plumbing tips. If you wind up with a future plumbing problem, the advice you have learned from this article will get you through it.
Los Angeles CA